检测项目（部分）
苯
馏程
开杯闪点
正己烷
氨
1，4-氧氮杂环己烷
其它色谱杂质
全部参数
易燃液体初沸点
外观
甲基环己烷
不挥发物
色度
闭杯闪点
密度
硫
电导率
纯度
检测样品（部分）
工业用环己烷
工业用1，4--氧氮杂环己烷(吗啉)
石油产品（馏分燃料、混合二甲苯、蜡油、渣油、原油、油浆、苯、甲苯、环己烷等）
检测标准（部分）
本部分适用于工作场所空气中蒸气态环己烷和甲基环己烷浓度的检测。
本标准适用于铂系苯加氢制环己烷催化剂中铂（Pt)、氧化钠（Na2O)、三氧化二铁（Fe2O3)、烧失量以及水（H2O）质量分数的测定。
This method is specified using ISO 3308 smoking parameters. This document provides an alternative
method to that specified in ISO 22634-1 with a different clean-up and a shorter total analytical run
allowing a potential increase of sample throughput in comparison with ISO 22634-1.
This method was validated using ISO 3308 smoking parameters and is technically compatible with other smoking regimes.
This document provides an alternative method to that specified in ISO 22634-1 with a different clean- up which is less time consuming and with a reduced analytical run allowing a potential increase of sample throughput in comparison with ISO 22634-1.
This method is for determining phenol at concentrations from 0.1 to 2.0 mass-ppm in light aromatic hydrocarbons such as benzene ethylbenzene cumene toluene and xylene as well as cyclohexane by visible spectrophotometry. Higher concentrations can be determined by diluting the sample. The presence of substituted phenols may cause a positive interference. Aldehydes ketones ethers alcohols amines and sulfur compounds will interfere if present.
1.1 This specification covers a grade of benzene known as Low Toluene Low Dioxane (LTLD) Benzene.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard an observed value or a calculated value shall be rounded off x201C;to the nearest unitx201D; in the last right-hand digit used in expressing the specification limit in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 Consult current OSHA regulations supplier''s Material Safety Data Sheets and local regulations for all materials used in this specification.
1.1 This specification covers a grade of benzene known as Low Toluene Low Dioxane (LTLD) Benzene.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard
an observed value or a calculated value shall be rounded off x201C;to the nearest unitx201D; in the last right-hand digit used in expressing the specification limit
in accordance with the rounding-off method of Practice E 29
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 Consult current OSHA regulations supplier''s Material Safety Data Sheets and local regulations for all materials used in this specification.
1.1 This standard is for use in calculating the weight and volume of benzene toluene mixed xylenes styrene ortho-xylene meta-xylene para-xylene cumene ethylbenzene 300 to 350176;F and 350 to 400176;F aromatic hydrocarbons and cyclohexane. A method is given for calculating the volume at 60176;F from an observed volume at t176;F. Table 1 lists the density in pounds per gallon at 60176;F for high purity chemicals.
1.2 Calculated results shall be rounded off in accordance with the rounding-off method of Practice E 29.
1.3 This standard does not purport to address all of the safety concerns if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.1 This specification covers a grade of benzene known as Low Toluene Low Dioxane (LTLD) Benzene.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 Consult current OSHA regulations supplier’s Safety Data Sheets and local regulations for all materials used in this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This test method covers the determination of the purity of cyclohexane by gas chromatography.
1.2 This test method has been found applicable to the measurement of impurities such as those found in Table 1 which are impurities that may be found in cyclohexane. The impurities can be analyzed over a range of 1 to 400 mg/kg by this method but may be applicable to a wider range.
1.3 The limit of detection is 1 mg/kg.
1.4 In determining the conformance of the test results using this test method to applicable specifications results shall be rounded off in accordance with the rounding-off method of Practice E29.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety health and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see Section 8.
【中国标准分类】 G16 有机化工原料 【国际标准分类】 71.080.10-脂族烃
1.1 This method covers the determination of extinction (absorbance) of carbon black cyclohexane extract at 386 nm using a UV spectrophotometer.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
检测优势
检测资质（部分）
检测实验室（部分）
合作客户（部分）
检测报告作用
1、可以帮助生产商识别产品的潜在问题或缺陷，并及时改进生产工艺，保障产品的品质和安全性。
2、可以为生产商提供科学的数据，证明其产品符合国际、国家和地区相关标准和规定，从而增强产品的市场竞争力。
3、可以评估产品的质量和安全性，确保产品能够达到预期效果，同时减少潜在的健康和安全风险。
4、可以帮助生产商构建品牌形象，提高品牌信誉度，并促进产品的销售和市场推广。
5、可以确定性能和特性以及元素，例如力学性能、化学性质、物理性能、热学性能等，从而为产品设计、制造和使用提供参考。
6、可以评估产品是否含有有毒有害成分，以及是否符合环保要求，从而保障产品的安全性。
检测流程
1、中析研究所接受客户委托，为客户提供检测服务
2、客户可选择寄送样品或由我们的工程师进行采样，以确保样品的准确性和可靠性。
3、我们的工程师会对样品进行初步评估，并提供报价，以便客户了解检测成本。
4、双方将就检测项目进行详细沟通，并签署保密协议，以保证客户信息的保密性。在此基础上，我们将进行测试试验.
5、在检测过程中，我们将与客户进行密切沟通，以便随时调整测试方案，确保测试进度。
6、试验测试通常在7-15个工作日内完成，具体时间根据样品的类型和数量而定。
7、出具检测样品报告，以便客户了解测试结果和检测数据，为客户提供有力的支持和帮助。
以上为环己烷检测的检测内容，如需更多内容以及服务请联系在线工程师。
