粗集料检测

1.1 This test method covers the determination of the average density of a quantity of coarse aggregate particles (not including the volume of voids between the particles) the relative density (specific gravity) and the absorption of the coarse aggregate. Depending on the procedure used the density (kg/m³ (lb/ft³)) is expressed as oven-dry (OD) or as apparent density. Likewise relative density (specific gravity) is expressed as OD SSD or as apparent relative density (apparent specific gravity). The OD density and OD relative density are determined after drying the aggregate. The SSD density SSD relative density and absorption are determined after soaking the aggregate in water for a prescribed duration.

1.2 This test method is used to determine the density of the essentially solid portion of a large number of aggregate particles and provides an average value representing the sample. Distinction is made between the density of aggregate particles as determined by this test method and the bulk density of aggregates as determined by Test Method C 29/C 29M which includes the volume of voids between the particles of aggregates.

1.3 This test method is not intended to be used with lightweight aggregates.

1.4 The values stated in SI units are to be regarded as the standard for conducting the tests. The test results for density shall be reported in either SI units or inch-pound units as appropriate for the use to be made of the results.

1.5 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.

This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.1 This test method covers the determination of the average density of a quantity of coarse aggregate particles (not including the volume of voids between the particles) as appropriate for the use to be made of the results.

1.5 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.

1.6 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The test has been widely used as an indicator of the relative quality or competence of various sources of aggregate having similar mineral compositions. The results do not automatically permit valid comparisons to be made between sources distinctly different in origin composition or structure. Assign specification limits with extreme care in consideration of available aggregate types and their performance history in specific end uses.

1.1 This test method covers testing sizes of coarse aggregate larger than 19 mm (x00BE; in.) for resistance to degradation using the Los Angeles testing machine (Note 1).

Note 18212;A procedure for testing coarse aggregate smaller than 37.5 mm (1x00BD; in.) is covered in Test Method C 131.

1.2 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.3 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.

1.1 This test method covers testing sizes of coarse aggregate larger than 19 mm (3/4 in.) for resistance to degradation using the Los Angeles testing machine (1).

Note 18212;A procedure for testing coarse aggregate smaller than 37.5 mm (1 1/2 in.) is covered in Test Method C 131.

1.2 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.3 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.

1.1 This specification covers crushed stone crushed hydraulic-cement concrete crushed blast-furnace slag crushed gravel crushed expanded shale crushed expanded clay and crushed expanded slate suitable for use in bituminous paving mixtures as described in Specifications D 3515 or D 4215.

Note 18212;Other slags having demonstrated a satisfactory service record may be used.

1.2 The values stated in SI units are to be regarded as standard. Inch-pound units shown in parentheses are for information only.

1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

This practice provides standard requirements for evaluating frost-susceptible coarse aggregate in air-entrained concrete subjected to freezing and thawing in accordance with Test Method C 666/C 666M.

Concrete containing frost-resistant paste may not be resistant to freezing and thawing if it contains coarse aggregate that becomes critically saturated. An aggregate particle is considered to be critically saturated when there is insufficient unfilled pore space to accommodate the expansion of water that accompanies the freezing.

The potential of the coarse aggregate to cause damage due to cycles of freezing and thawing is evaluated by Test Method C 666/C 666M.

1.1 This specification covers materials for use in hydraulic-cement concrete mixtures to be placed by shotcreting. It does not cover mixing placement curing or protection of the concrete placed by shotcreting.

1.2 This specification covers materials for both wet-mix and dry-mix shotcreting.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of the standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This practice provides standard requirements for evaluating frost-susceptible coarse aggregate in air-entrained concrete subjected to freezing and thawing in accordance with Test Method C 666/C 666M.

Concrete containing frost-resistant paste may not be resistant to freezing and thawing if it contains coarse aggregate that becomes critically saturated. An aggregate particle is considered to be critically saturated when there is insufficient unfilled pore space to accommodate the expansion of water that accompanies the freezing.

The potential of the coarse aggregate to cause damage due to cycles of freezing and thawing is evaluated by Test Method C 666/C 666M.

1.1 This practice covers procedures for making and curing test specimens for evaluating frost resistance of normal-weight coarse aggregates in air-entrained concrete in accordance with Test Method C 666/C 666M Procedure A or B.

1.2 The values stated in either inch-pound or SI units shall be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.3 This practice does not purport to address all the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning-Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged use.)

1.1 This specification covers the use of coarse aggregates not traditionally used in bituminous paving mixtures. These nontraditional aggregates can be described as any aggregate other than those described in Specifications D 692 D 693 D 1139 and D 5106 (crushed stone steel furnace slag and crushed gravel) suitable for use in bituminous paving mixtures as described in Specifications d 3515 or D 4215.

1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.

The Micro-Deval abrasion test is a test of coarse aggregate to determine abrasion loss in the presence of water and an abrasive charge. Many aggregates are more susceptible when wet than dry and the use of water in this test incorporates this reduction in resistance in degradation in contrast to some other tests which are conducted on dry aggregate. The test results are helpful in evaluating the toughness/abrasion resistance of coarse aggregate subject to abrasion when adequate information is not available from service records.

The Micro-Deval abrasion test is useful for detecting changes in properties of aggregate produced from an aggregate source as part of a quality control or quality assurance process.

1.1 This method covers a procedure for testing coarse aggregate for resistance to abrasion using the Micro-Deval apparatus.

1.2 The values stated in SI units are to be regarded as the standard.

1.3 The text of this method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.

1.4 This procedure may involve hazardous materials operations and equipment. This standard does not purport to address all of the safety concerns

国外标准 ASTM D6155-2019 沥青铺设混合物用非传统粗集料规格

【适用范围】

1.1 This specification covers the use of coarse aggregates not traditionally used in asphalt paving mixtures. These nontraditional aggregates can be described as any aggregate other than those described in Specifications D692/D692M D693 D1139/D1139M and D5106 (crushed stone and crushed gravel) suitable for use in asphalt paving mixtures as described in Specification D3515 or D4215.

1.2 The text of this specification references notes and footnotes that provides explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.

1.4 This standard does not purport to address all of the safety concerns associated with its use. It is the

【中国标准分类】  Q13  建材产品 【国际标准分类】  93.080.20-道路建筑材料

国外标准 ASTM D692/D692M-2015 沥青铺路混合料用粗集料的规格

【适用范围】1.1 This specification covers crushed stone as described in Specifications D3515 or D4215. Note 1: Other slags having demonstrated a satisfactory service record may be used. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

【中国标准分类】  Q13  建材产品 【国际标准分类】  93.080.10-道路建筑

国外标准 ASTM D6155-2015 沥青铺设混合物用非传统粗集料规格

【适用范围】1.1 This specification covers the use of coarse aggregates not traditionally used in bituminous paving mixtures. These nontraditional aggregates can be described as any aggregate other than those described in Specifications D692 D693 D1139 and D5106 as described in Specifications D3515 or D4215. 1.2 The text of this specification references notes and footnotes that provides explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. 1.4 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

【中国标准分类】  Q13  建材产品 【国际标准分类】  93.080.20-道路建筑材料

国外标准 ASTM C136/C136M-2014 细集料和粗集料筛析试验方法

【适用范围】1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving. 1.2 Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions. Instructions are included for sieve analysis of such aggregates. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. Specification E11 cites the following with respect to SI units versus inch-pound units as standard. “The values stated in SI units shall be considered standard for the dimensions of the sieve cloth openings and the wire diameters used in the sieve cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames pans ” and covers. 1.4 This standard does not purport to address all of the safety concerns

国外标准 ASTM C131/C131M-2014 粗集料密度、相对密度(比重)和吸收性的试验方法

【适用范围】1.1 This test method covers the determination of the average density of a quantity of coarse aggregate particles (not including the volume of voids between the particles) the density (kg/m3 (lb/ft3)) is expressed as oven-dry (OD) and absorption are determined after soaking the aggregate in water for a prescribed duration. 1.2 This test method is used to determine the density of the essentially solid portion of a large number of aggregate particles and provides an average value representing the sample. Distinction is made between the density of aggregate particles as determined by this test method and the bulk density of aggregates as determined by Test Method C29/C29M which includes the volume of voids between the particles of aggregates. 1.3 This test method is not intended to be used with lightweight aggregates that comply with Specification C332 Group I aggregates. 1.4 The values stated in SI units are to be regarded as the standard for conducting the tests. The test results for density shall be reported in either SI units or inch-pound units as appropriate for the use to be made of the results. 1.5 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method. 1.6 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and hea

【中国标准分类】  Q13  建材产品 【国际标准分类】  91.100.30-混凝土和混凝土制品

国外标准 ASTM D6928-2010 用超小型戴佛磨损试验仪测定粗集料耐磨损性的试验方法

【适用范围】

The Micro-Deval abrasion test is a test of coarse aggregate to determine abrasion loss in the presence of water and an abrasive charge. Many aggregates are more susceptible to abrasion when wet than dry and the use of water in this test incorporates this reduction in resistance to degradation in contrast to some other tests which are conducted on dry aggregate. The test results are helpful in evaluating the toughness/abrasion resistance of coarse aggregate subject to abrasion when adequate information is not available from service records.

The Micro-Deval abrasion test is useful for detecting changes in properties of aggregate produced from an aggregate source as part of a quality control or quality assurance process.

1.1 This test method covers a procedure for testing coarse aggregate for resistance to abrasion using the Micro-Deval apparatus.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 The text of this method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.

1.4 This procedure may involve hazardous materials associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

【中国标准分类】  Q13  建材产品 【国际标准分类】  91.100.15-矿物材料和产品

国外标准 ASTM D4791-2010 扁平颗粒和长颗粒或粗集料中扁平颗粒和长颗粒的测试方法

【适用范围】

The particles shape of course aggregates influences the properties of some construction materials and may affect their placement and consolidation.

This test method provides a means for checking compliance with specifications that limit such particles or to determine the relative shape characteristics of coarse aggregates.

1.1 This test method covers the determination of the percentages of flat particles elongated particles or flat and elongated particles in coarse aggregates. Two procedures Method A and Method B are presented in this standard. Method A is a reflection of the original procedure as developed prior to Superpave and is intended for all non-Superpave applications. Method B is a comparison of the maximum particle dimension to the minimum particle dimension and is intended for use with Superpave specifications.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.2.1 Exception 8212;(Regarding sieves per Specification E11) The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. When sieve mesh sizes are referenced the alternate inch-pound designations are provided for information purposes and enclosed in parenthesis.

1.3 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

【中国标准分类】  Q13  建材产品 【国际标准分类】  91.100.30-混凝土和混凝土制品

国外标准 ASTM C131-2006 通过使用洛杉矶机器测量磨损与冲击对小尺寸粗集料抗裂解性的试验方法

【适用范围】

This test has been widely used as an indicator of the relative quality or competence of various sources of aggregate having similar mineral compositions. The results do not automatically permit valid comparisons to be made between sources distinctly different in origin or structure. Assign specification limits with extreme care in consideration of available aggregate types and their performance history in specific end uses.

1.1 This test method covers a procedure for testing sizes of coarse aggregate smaller than 37.5 mm (11/ 2 in.) for resistance to degradation using the Los Angeles testing machine (Note 1).

Note 18212;A procedure for testing coarse aggregate larger than 19.0 mm (3/4 in.) is covered in Test Method C 535.

1.2 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.

This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

【中国标准分类】  Q13  建材产品 【国际标准分类】  91.100.30-混凝土和混凝土制品

有问题可咨询检测工程师，我们的检测工程师收到信息会在 第一时间 联系您...

检测优势

服务范围广泛 中析研究所检测范围覆盖高分子材料、金属材料、橡胶材料、包装材料、纺织品、建筑材料、化工产品及原料、生物试验、机械产品、能源、药品、食品等多个领域。

检测仪器齐全 拥有中大型仪器以及小型仪器1000余台，拥有傅里叶变换红外光谱仪、高效液相色谱仪、气相色谱-质谱联用仪、可程式高低温试验箱、耐老化试验箱、电子万能试验机等多种仪器。

多所检测实验室 建设有生物实验室、力学实验室、理化试验室、机械实验室、非标实验室、热学实验室、电学实验室、光学实验室等多个领域的实验室，能够分门别类对检测样品进行检测。

多项荣誉资质 中析研究所旗下实验室取得了“CMA检验检测机构资质认定证书”、“CNAS认可证书”、“ISO证书”、“国家高新技术企业证书”以及“中国检验检测学会会员”等多个荣誉资质。

检测资质（部分）

检测实验室（部分）

合作客户（部分）

检测报告作用

1、可以帮助生产商识别产品的潜在问题或缺陷，并及时改进生产工艺，保障产品的品质和安全性。

2、可以为生产商提供科学的数据，证明其产品符合国际、国家和地区相关标准和规定，从而增强产品的市场竞争力。

3、可以评估产品的质量和安全性，确保产品能够达到预期效果，同时减少潜在的健康和安全风险。

4、可以帮助生产商构建品牌形象，提高品牌信誉度，并促进产品的销售和市场推广。

5、可以确定性能和特性以及元素，例如力学性能、化学性质、物理性能、热学性能等，从而为产品设计、制造和使用提供参考。

6、可以评估产品是否含有有毒有害成分，以及是否符合环保要求，从而保障产品的安全性。

检测流程

1、中析研究所接受客户委托，为客户提供检测服务

2、客户可选择寄送样品或由我们的工程师进行采样，以确保样品的准确性和可靠性。

3、我们的工程师会对样品进行初步评估，并提供报价，以便客户了解检测成本。

4、双方将就检测项目进行详细沟通，并签署保密协议，以保证客户信息的保密性。在此基础上，我们将进行测试试验.

5、在检测过程中，我们将与客户进行密切沟通，以便随时调整测试方案，确保测试进度。

6、试验测试通常在7-15个工作日内完成，具体时间根据样品的类型和数量而定。

7、出具检测样品报告，以便客户了解测试结果和检测数据，为客户提供有力的支持和帮助。

以上为粗集料检测的检测内容，如需更多内容以及服务请联系在线工程师。

上一篇：皮革和毛皮检测

下一篇：建筑结构检测