供电设备检测

供电设备检测简介

发布时间：2023-04-21 11:22:15

更新时间：2025-05-14 23:55:03

咨询点击量：127

第三方供电设备检测机构北京中科光析科学技术研究所科研分析中心作为综合性研究所检测中心，旗下实验室拥有CMA检测资质，检测设备齐全，数据科学可靠，7-15个工作日便可出具供电设备检测报告。检测样品包含电动汽车充电系统-非车载传导供电设备、不间断供电设备、电动汽车传导充电-供电设备、电动汽车传导充电互操作性——供电设备、轨道交通地面供电设备、供电设备等。

咨询检测服务预约工程师

获取检测报价？

了解检测仪器？

查看报告模板？

立即咨询

供电设备检测内容

检测项目（部分）

电压暂降、短时中断和电压变化

静电放电

保护接地导体连续性丢失测试

浪涌

辐射抗扰度

电快速瞬变脉冲群抗扰度

电压波动和闪烁

谐波电流发射

工频磁场抗扰度

工频磁场

直流充电互操作性测试

充电连接控制时序测试

电快速瞬变脉冲群

其他充电故障测试

检测样品（部分）

电动汽车充电系统-非车载传导供电设备

不间断供电设备

电动汽车传导充电-供电设备

电动汽车传导充电互操作性——供电设备

轨道交通地面供电设备

供电设备

检测标准（部分）

国家标准 GB/T 15474-1995 核电厂仪表和控制系统及其供电设备安全分级

【适用范围】

【中国标准分类】 L06 核仪器与核探测器【国际标准分类】 33.100-电磁兼容性(EMC)

国家标准 GB/T 24338.6-2018 轨道交通电磁兼容第5部分：地面供电设备和系统的发射与抗扰度

【适用范围】GB/T24338的本部分规定了轨道交通地面供电电子和电气设备与系统，包括设备的供电电源，设备自身的保护控制电路，以及变电站、自耦变压器、吸流变压器、变电站开关柜和本地电气开关等轨旁设备的电磁发射与抗扰度要求。
本部分不适用于工作电压为牵引供电电压的滤波器（如用于谐波抑制或功率因数补偿的滤波器）。通常滤波器需要独立的外壳和接入规定。如果有电磁发射限值要求，将在电子设备标准中规定。
本标准的限值也不适用于旨在产生有意发射的通信信号。
本部分考虑的频率范围为0GHz-400GHz，没有要求的频段不需要进行测试。
本部分适用于轨道交通地面供电用电气电子设备和系统，包括：
——变电站内对轨道交通系统供电的设备；
——轨旁的控制和整流设备，包括用于功率因数补偿装置；
——除受流器和相关的回流导体以外的轨道沿线供电接触网，包括轨道交通系统内用以转换牵引电压的变电站中的高压供电系统；
——轨旁的辅助电源设备，包括向货运编组站、检修站和车站供电的电源；
——与轨道牵引共用的其他非牵引供电电源。
本部分给出的抗扰度要求适用于：
——关键设备，如防护设备等；
——与牵引电力导线相连的设备；
——3m区域内的设备；
——10m区域内的设备且与3m区域内的设备有连接端口；
——l0m区域内的设备且连接有超过30m的电缆。
使用于居民区、商业区和轻工业区环境的供电设备和系统，即使安装于牵引变电所范围内，也应符合其他相关的通用电磁兼容标准。
本部分的抗扰度要求不适用于无法按表1～表6进行试验的电x设备。
注：如18MVA230kV转换成25kV的电源变压器。
本部分的要求也适用于地面装置。
本部分的具体规定应与GB/T24338.1通用规定一起使用。

【中国标准分类】 S35 机车车辆通用标准【国际标准分类】 29.280-电力牵引设备

国家标准 GB/T 34657.1-2017 电动汽车传导充电互操作性测试规范第1部分：供电设备

【适用范围】GB/T34657的本部分规定了电动汽车传导充电互操作性测试对供电设备的检验规则、测试条件、测试项目、测试方法及合格评判。
本部分适用于符合GB/T18487.1-2015规定的电动汽车供电设备，包括缆上控制与保护装置、交流充电桩、非车载充电机等。

【中国标准分类】 T35 车用电子、电气设备与仪表【国际标准分类】 43.040.99-其他道路车辆装置

国家标准 GB/T 37139-2018 直流供电设备的EMC测量方法要求

【适用范围】本标准规定了直流供电设备的电磁兼容性（EMC）要求，包括设备的分级、测量条件、产品文件、适用性、发射和抗扰度要求、测量不确定度、发射测量的标准符合性、抗扰度试验性能判据等要求。
本标准适用于同时满足以下条件的直流供电设备：
a）具有3.1.5定义的直流电源端口；
b）额定电压最大值不超过1500VDC。
如果没有相关的产品或产品类电磁兼容标准，则本标准适用。
本标准对所考虑的每种端口都规定了试验要求及对应测量／试验方法。

【中国标准分类】 L06 电子元器件与信息技术综合【国际标准分类】 33.100-电磁兼容性(EMC)

国家标准 GB/T 39752-2021 电动汽车供电设备安全要求及试验规范

【适用范围】本标准规定了电动汽车供电设备(以下简称“供电设备”)的安全要求、试验导则和试验方法。
本标准适用于额定输出电压为1000VAC或1500VDC及以下各类型供电设备，包括充电模式2、充电模式3和充电模式4的供电设备，不作为公共用途使用、在特殊条件下使用的供电设备(如防爆型、液冷型、海拔2000m以上高原使用的供电设备等)也适用于本标准，并需要结合相关标准的要求。
对于供电设备的独立电气附件、辅助材料(如连接装置、线缆、绝缘材料等)需根据具体产品标准，与本标准结合使用。
本标准涉及到供电设备在符合正确使用规程，但可能发生操作失误的情况下，由于电击危险、能量危险、机械危险、高温危险、着火蔓延危险、声压危险、失控危险等造成的设备严重损坏和重大人身危害情况。
本标准不涉及以下内容：
--与运输包装、不恰当安装和应用相关的安全要求；
--电磁兼容要求；
--信息安全要求；
--因故意破坏和其他有目的行为所引起的安全问题；
--其他与安全无关的功能和性能要求。

【中国标准分类】 T35 车用电子、电气设备与仪表【国际标准分类】 43.040.99-其他道路车辆装置

行业标准 TB/T 2558-1995 空调客车供电设备技术条件

【适用范围】

【中国标准分类】 S81 铁路车辆【国际标准分类】 29.280-电力牵引设备

行业标准 TB/T 2805-1997 电气化铁道牵引变电所供电设备绝缘水平

【适用范围】本标准适用于电气化铁道牵引变电所内主变压器低压侧电气设备及开闭所，分区所、自耦变压器所等的下列电气设备，其绝缘水平为相对地。rna）变压器类：电力变压器、电磁式电压互感器；nb）高压电器：断路器、隔离开关、负荷开关、熔断器、电流互感器、组合电器等、并联电容补偿装置、串联电容补偿装置；nc）高压电力电缆；nd）电站瓷绝缘，穿墙套管；ne）避雷器瓷套。

【中国标准分类】 F83 牵引供电【国际标准分类】 27.120.20-核电站、安全

国际标准 IEC 61558-1-2005 动力电变压器--动力供电设备和类似电器的安全--第1部分:一般要求和试验.

【适用范围】This International Standard deals with safety aspects of power transformers power supplies nreactors and similar products such as electrical thermal and mechanical safety.nThis standard also applies to transformers power supplies switch mode power supplies nand reactors incorporating electronic circuits.nThis standard does not apply to external circuits and their components intended to benconnected to the input and output terminals or socket-outlets of the transformers powernsupplies and switch mode power supplies and reactors.

【中国标准分类】 K09 电工综合【国际标准分类】 29.180-变压器、电抗器

国际标准 IEC 61558-1-1998 动力变压器、供电设备和类似装置的安全--第2-10部分:分离变压器高绝缘等级和输出电压rn超过1 000 V分离变压器的特定需求和试验

【适用范围】Replacement:nThis part of IEC 61558 deals with the safety of separating transformers with high insulationnlevel and separating transformers with output voltages exceeding 1 000 V. Transformersnincorporating electronic circuits are also covered by this standard.nNOTE 1 Safety includes electrical thermal and mechanical aspects.nUnless otherwise specified from here onward the term transformer covers separatingntransformers with high insulation level and separating transformers with output voltagesnexceeding 1 000 V a.c or 1 500 V d.c .nThis Part 2-10 is applicable to stationary or portable single-phase or polyphase air-cooledn(natural or forced) independent or associated dry-type transformers. The windings may benencapsulated or non-encapsulated.nThis standard is applicable to transformers and power supply (linear) with internalnoperational frequencies not exceeding 500 Hz.nThis standard used in combination with Part 2-16 for switch mode power supply unitsn(SMPS) is also applicable to power supplies with internal operational frequencies higher thann500 Hz. Where the two requirements are in conflict the most severe take precedence.nThe rated supply voltage does not exceed 1 000 V a.c. and the rated supply frequency andnthe internal operating frequency do not exceed 500 Hz.nThe rated output does not exceed:n– 25 kVA for single-phase transformers;n– 40 kVA for polyphase transformers.nThis Part 2-10 is applicable to transformers without limitation of the rated output subject tonan agreement between the purchaser and the manufacturer.nWhere applicable the no-load output voltage or the rated output voltage:n– does not exceed 1 000 V a.c. or 1 500 V d.c. for separating transformers with highninsulation level;n– does exceed 1 000 V a. c or 1 500 V d.c. and does not exceed 15 000 V a.c. or 15 000 Vnd.c. for separating transformer with output voltage exceed 1 000 V.nThis Part 2-10 is not applicable to:n– transformers covered by IEC 60076-11;n– 6 – IEC 61558-2-10:2014 ? IEC 2014n– neon transformers covered by IEC 61050 andn– power supplies and converters for use with or in products according to IEC 61347-2-10.nThis Part 2-10 is not applicable to external circuits and their components intended to benconnected to the input terminals and output terminals of the transformers.nTransformers covered by this Part 2-10 are used only in applications where double ornreinforced insulation between circuits is not required by the installation rules or by the endnproduct standard.nNOTE 2 Normally the transformers are intended to be used with equipment to provide voltages different from thensupply voltage for the functional requirements of the equipment. The protection against electric shock can benprovided (or completed) by other features of the equipment such as the body. Parts of output circuits can benconnected to the input circuits or to protective earth.nThis Part 2-10 is applicable to transformers associated with specific equipment to the extentndecided upon by the relevant IEC technical committees.nNOTE 3 Attention is drawn to the following:n– for transformers intended to be used in vehicles on board ships and aircraft additional requirements (fromnother applicable standards national rules etc.) can be necessary;n– measures to protect the enclosure and the components inside the enclosure against external influences suchnas fungus vermin termites solar-radiation and icing can also be considered;n– the different conditions for transportation storage and operation of the can also be considered;n– additional requirements in accordance with other appropriate standards and national rules can be applicable tontransformers intended for use in special environments such as tropical environment.nNOTE 4 Future technological development of transformers can necessitate a need to increase the upper limit ofnthe frequencies until then this Part 2-10 can be used as a guidance document.

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国际标准 IEC 61558-2-12-2001 电动汽车导电充电系统--第25部分:依靠电隔离保护的直流电动汽车供电设备

【适用范围】This document applies to the DC EV supply equipment for charging electric road vehicles with a rated supply voltage of up to 480 V AC or up to 600 V DC with rated output voltage not exceeding 120 V DC and output currents not exceeding 100 A DC.
This document provides the requirements for the DC EV supply equipment where the secondary circuit is protected from the primary circuit by electrical separation.
Requirements for bi-directional power flow are not covered in this document.
This document also provides the requirements for the control and the communication between DC EV supply equipment and an EV.This document also provides the requirements for the control and the communication between DC EV supply equipment and an EV.
This document also applies to DC EV supply equipment supplied from on-site storage systems.
The aspects covered in this document include:
• characteristics and operating conditions of the DC EV supply equipment;
• specification of the connection between the DC EV supply equipment and the EV;
• requirements for electrical safety for the DC EV supply equipment.
Additional requirements can apply to equipment designed for specific environments or
conditions for example:
• DC EV supply equipment located in hazardous areas where flammable gas or vapour and/or combustible materials fuels or other combustible or explosive materials are present;
• DC EV supply equipment designed to be installed at an altitude of more than 2 000 m;
• DC EV supply equipment intended to be used on-board ships.
Requirements for electrical devices and components used in DC EV supply equipment are not included in this document and are covered by their specific product standards.
This document does not apply to:
• safety aspects related to maintenance;
• charging of trolley buses rail vehicles industrial trucks and vehicles designed primarily for use off-road;
• equipment on the EV;
• EMC requirements for equipment on the EV while connected which are covered in
IEC 61851-21-1;
• charging the RESS off-board the EV.

【中国标准分类】 T90 无轨电车与其他车辆【国际标准分类】 43.120-电车

国外标准 BS EN 54-4-1998 火灾探测和火灾警报系统.供电设备

【适用范围】This European Standard specifies requirements methods of test and performance criteria for power supply equipment (see component L of figure 1 of EN 54-1) of fire detection and fire alarm systems installed in buildings.nNOTE. Power supply equipment with special characteristics developed for particular applications is not necessarily the subject of this standard and may require further tests.

【中国标准分类】 C81 消防【国际标准分类】 13.220.20-防火

国外标准 BS 5148-1975 道路车辆交流电源供电设备用小型连接器规范

【适用范围】

【中国标准分类】 T36 车用电子、电气设备与仪表【国际标准分类】 29.120.30-插头、插座、联接器

国外标准 BS EN 50121-5-2015 铁路设施.电磁兼容性.固定供电设备的辐射和抗干扰

【适用范围】

【中国标准分类】铁路综合【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-1-2007 电源变压器、供电设备、反应器和类似产品的安全性.通用分离变压器和有分离变压器的供电设备的详细要求和试验

【适用范围】Replacement:nThis part of IEC 61558 deals with safety aspects of separating transformers and powernsupplies incorporating separating transformers such as electrical thermal and mechanicalnsafety.nThis Part 2-1 is applicable to separating transformers and power supplies incorporatingnboth separating transformers and electronic circuits. This Part 2-1 is not applicable tonexternal circuits and their components intended to be connected to the input terminals outputnterminals or socket-outlets of the transformers and power supplies.nThis Part 2-1 does not apply to transformers covered by IEC 60076-11.nThis Part 2-1 applies to stationary or portable single-phase or polyphase air-cooledn(natural or forced) independent and associated separating transformers and powernsupplies having a rated supply voltage not exceeding 1 000 V a.c. a rated supply andninternal operating frequency not exceeding 500 Hz.nThe rated output does not exceed:n– 1 kVA for single-phase separating transformers and single-phase power suppliesnincorporating separating transformers;n– 5 kVA for poly-phase separating transformers and poly-phase power suppliesnincorporating separating transformers.nThis Part 2-1 is applicable to separating transformers and power supplies incorporatingnseparating transformers without limitation of the rated output subject to an agreementnbetween the purchaser and the manufacturer.nThis Part 2-1 is applicable to dry-type transformers. The windings may be encapsulated ornnon-encapsulated.nThe no-load output voltage or the rated output voltage does not exceed 1 000 V a.c. orn1 415 V ripple-free d.c. For independent separating transformers and independent powernsupplies the no-load output voltage and / or the rated output voltage is not less than 50nV a.c. or 120 V ripple-free d.c.nnSeparating transformers covered by this Part 2-1 are used only in applications wherendouble or reinforced insulation between circuits is not required by the installation rules ornby the end product standard.nNOTE 1 Normally the separating transformers and power supplies incorporating separating transformersnare intended to be used with equipment to provide voltages different from the supply voltage for the functionalnrequirements of the equipment. The protection against electric shock may be provided (or completed) by othernfeatures of the equipment such as the body. Parts of output circuits may be connected to the input circuits ornto protective earth.nThis Part 2-1 is applicable to separating transformers and power supplies incorporatingnseparating transformers associated with specific equipment to the extent decided upon bynthe relevant IEC technical committees.nNOTE 2 Attention is drawn to the following:n– for separating transformers and power supplies incorporating separating transformers intended to be usednin vehicles on board ships and aircraft additional requirements (from other applicable standards nationalnrules etc.) may be necessary;n– measures to protect the enclosure and the components inside the enclosure against external influences suchnas fungus vermin termites solar-radiation and icing should also be considered;n– the different conditions for transportation storage and operation of the separating transformers and powernsupplies incorporating separating transformers should also be considered;n– additional requirements in accordance with other appropriate standards and national rules may be applicable tonseparating transformers and power supplies incorporating separating transformers intended for use innspecial environments such as tropical environment.nNOTE 3 Future technological development of separating transformers and power supplies incorporatingnseparating transformers may necessitate a need to increase the upper limit of the frequencies until then thisnPart 2-1 may be used as a guidance document.

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-2-2007 电力变压器、供电设备、反应器和类似产品的安全性.控制变压器和有控制变压器的供电设备的详细要求和试验

【适用范围】Replacement:nThis part of IEC 61558 deals with safety aspects of control transformers and power suppliesnincorporating control transformers such as electrical thermal and mechanical safety.nThis Part 2-2 is applicable to control transformers and power supplies incorporating bothncontrol transformers and electronic circuits. This Part 2-2 is not applicable to externalncircuits and their components intended to be connected to the input terminals output terminalsnor socket-outlets of the transformer and power supplies.nThis Part 2-2 does not apply to transformers covered by IEC 60076-11.nThis Part 2-2 applies to stationary or portable single-phase or poly-phase air-cooled (naturalnor forced) independent or associated control transformers and power suppliesnincorporating a control transformer having a rated supply voltage not exceeding 1 000 Vna.c. and rated supply and internal operating frequency not exceeding 500 Hz.nThe rated thermal output does not exceed:n– 25 kVA for single-phase control transformers and power supplies incorporating controlntransformers;n– 40 kVA for poly-phase control transformers and power supplies incorporating controlntransformers.nThis Part 2-2 is applicable to control transformers and power supplies incorporating controlntransformers without limitation of the rated output subject to an agreement between thenpurchaser and the manufacturer.nThis Part 2-2 is applicable to dry-type transformers. The windings may be encapsulated ornnon-encapsulated.nThe no-load output voltage or the rated output voltage does not exceed 1 000 V a.c. orn1 415 V ripple-free d.c.nFor independent control transformers and independent power supplies incorporatingncontrol transformers the no-load output voltage and / or the rated output voltage is notnless than 50 V a.c. or 120 V ripple free d.c.nControl transformers covered by this Part 2-2 are used only in applications where double ornreinforced insulation between circuits is not required by the installation rules or by the endnproduct standard.nNOTE 1 Normally the control transformers and power supplies incorporating control transformers arenintended to be used with equipment to provide voltages different from the supply voltage for the functionalnrequirements of the equipment. The protection against electric shock may be provided (or completed) by othernfeatures of the equipment such as the body. Parts of output circuits may be connected to the input circuits or tonprotective earth.nThis Part 2-2 is applicable to control transformers and power supplies incorporating controlntransformers associated with specific equipment to the extent decided upon by the relevantnIEC technical committees.nNOTE 2 Attention is drawn to the following:n– for control transformers and power supplies incorporating control transformers intended to be used innvehicles on board ships and on board aircraft additional requirements (from other applicable standards nnational rules etc.) may be necessary;n– measures to protect the enclosure and the components inside the enclosure against external influences suchnas fungus vermin termites solar-radiation and icing should also be considered ;n– the different conditions for transportation storage and operation of the control transformers and powernsupplies incorporating control transformers should also be considered;n– additional requirements in accordance with other appropriate standards and national rules may be applicable toncontrol transformers and power supplies incorporating control transformers intended for use in specialnenvironments such as tropical environments.nNOTE 3 Future technological development of control transformers and power supplies incorporating controlntransformers may necessitate a need to increase the upper limit of the frequencies until then this Part 2-2 may benused as a guidance document.

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-9-2003 电力变压器、供电设备及类似设备的安全.Ⅲ类手抽式钨丝灯的变压器的特殊要求

【适用范围】To be read in conjunction with BS EN 61558-1:1998

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-19-2001 电源变压器、供电设备及类似设备的安全性.扰动衰减变压器的特殊要求

【适用范围】Applies to stationary or portable single-phase or poly-phase air cooled (natural or forced) isolating or safety transformers.

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-15-2001 电源变压器供电设备及类似设备的安全性.医用分体供电变压器详细要求

【适用范围】Applies to stationary single-phase or polyphase air-cooled isolatingtransformers for the supply of group II medical locations. To be read in conjunction with BS EN 61558-1

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-12-2001 电力变压器供电设备及类似设备的安全性.恒压变压器的详细要求

【适用范围】To be read in conjunction with BS EN 61558-1:1998

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-20-2001 电源变压器、供电设备及类似设备的安全性.小型电抗器用特殊要求

【适用范围】Applies to small reactors including alternating current premagnetised and current compensated reactors. To be read in conjunction with BS EN 61558-1:1998

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-23-2001 电源变压器、供电设备及类似设备安全性.建筑工地变压器专门要求

【适用范围】Applies to stationary or portable single-phase or poly-phase air-cooled isolating or safety isolating transformers To be read in conjunction with BS EN 61558-1:1998

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-8-1999 电力变压器、供电设备及类似设备的安全.铃声和钟声变压器的特殊要求

【适用范围】

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-4-1998 电力变压器、供电设备及类似设备的安全.一般用途隔离变压器的特殊要求

【适用范围】

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-17-1998 电力变压器、供电设备及类似设备的安全.开关式供电系统用变压器的特殊要求

【适用范围】

【中国标准分类】 K41 输变电设备【国际标准分类】 29.180-变压器、电抗器

国外标准 BS EN 61558-2-1-1998 电力变压器、供电设备及类似设备的安全.一般用途分离变压器的特殊要求

【适用范围】